Each tool brings us an advantage. In physical terms, it is usually a mechanical advantage. But never a thinking advantage. Tools sometimes make us think less. We don’t always anticipate what could go wrong if we use the wrong tool or use a tool in the wrong way. A screwdriver is not a lever or a chisel. A wrench is not a hammer.

Sharpest tool in the drawer

One of the most frequently used tools in any house is a knife. A sharp edge. Table knives. Steak knives. Knives to cut vegetables or remove the skin from fruit. A knife for spreading putty. A knife used in scrapbooking. A pocket knife. A hunting knife. A utility knife, which is usually a handle with replaceable razor blades.

All these knives were designed for specific purposes. Each one should be used as designed, and the user should make sure they are always cutting in a way that does not endanger them or those around them. Use the knife that is sharp enough for the job, has the right length, and that you can apply sufficient pressure to cut with. Sounds easy enough, right?

In my experience, the utility knife is the most mis-judged knife of all those above. In using a utility knife, people frequently use too much pressure so they can get the cut done. High amounts of force, applied to a fine edge, can often lead to a slip that could result in injury. In industries where these knives are used routinely, employees are taught proper cutting techniques, given cut-proof or cut-resistant gloves to wear on their non-cutting hand, and even given careful instruction on how to change the blade when it is too dull to properly cut.

If I buy that same knife at Home Depot, I won’t get that instruction. I might read the warnings, but they won’t all come to mind each time I pick the knife up. And a cut-proof glove? They’re a little pricey for the amount of time the average home owner might ever use the knife, so they don’t get purchased and kept with the knife.

Last week, I had to replace the thermostat in my home. A simple job, but it required a couple of short jumper wires. Three inches long with about three-quarters of an inch bare wire on each end. I couldn’t find my wire strippers – the tool that is designed to do exactly this task. And it does the task well with minimal risk. I did find my utility knife, and with careful consideration and deliberate action, used that tool to strip the wires. To do it safely took some effort. I didn’t just hold the knife to the insulation and cut toward the end. Too much possibility of nicking the wire or slipping and cutting something else. Work was done without injury. It just took longer and involved more risk.

Risk, ultimately, it the thing we are willing to trade for expediency. Does that make sense to you?

The next time you are faced with compromising on tool use, ask yourself what the true compromise is. As what you are giving up or willing to risk in order to get the job done. And if you have employees that you are accountable for, ask yourself if you would be willing to allow them the same risk.

Thanks, and let’s be careful out there.

Here are the tools I have seen mis-used the most in my life.

1. Screwdrivers – This simple tool is designed to translate force to rotate screws into and out of materials. there are several types, the most common being the phillips head and the slotted or regular. We use them as a pry bar, especially to open paint cans or put a bike tire on its rim. Not a good idea. At times we use them for the right thing, but we hold the object we are working on in a way that when the screwdriver slips, we could get a cut or even a puncture wound. Ouch!
2. Hammers – One person I know calls a hammer a “16 ounce wrench” because he uses a hammer to adjust things – to beat them into submission. Again, we use this tool mostly for what it was designed for, but many people don’t take the time to don even an inexpensive pair of safety glasses to provide protection from flying nails or materials that chip when they are hit.
3. Pliers, Channel-lock pliers, and any adjustable wrench. These tools are great, but their misuse can lead to aggravation. The biggest problem is using these tools for working with nuts and bolts. Anything other than socket wrenches, open-end wrenches or box wrenches used on a bolt head will compromise the geometry, making it harder to ever use the correct tool and creating sharp burrs. They also are prone to slipping, which leads to knuckle injuries.
4. Kitchen knives – When used to open that UPS package or as a pry bar to get those AA batteries loose from the remote, you are damaging the integrity of the blade, and making it less reliable when called upon to do the work you have it for. And that is when the knife slips off the green pepper and into your finger.
5. Scissors – Do you have one of those drawers in your house that is the repository for miscellaneous tools? I’ll bet the scissors in there are the most mis-used tool in the drawer. Mostly because they are used so frequently that they end up becoming the easiest thing to grab. Generally mis-used the same way a knife is. Here, the danger is in how we handle them when we start using them for alternative purposes.

Getting the right tool for the job is critical. Using it correctly is just as important. Do you have an experience where you didn’t think about the misuse of a tool until an accident happened? Let us all know about it, you might save us from injury.

Thanks, and let’s be careful out there.

Anna at abdpbt is responsible for the effort to Fight Listless Mondays. Find other list links on her blog. Her lists and the others linked there always give you something to think about, and may even make you smile!